長期使用雕刻機的人都知道，雕刻機臺面使用時間長了是很容易導致毛刺不平的。這樣的情況下機器進行雕刻的話就很容易導致板不平，雕刻的時候容易出現花刀，圖案毛刺多，且很容易直接把板雕錯，所以適當?shù)那逑磁_面是非常有必要的。那么木工雕刻機的臺面如何清洗呢?下面就讓小編來告訴大家兩個小方法。

先做好臺面大小的矩形洗底路徑圖，深度不要太深。關鍵的一點是對刀的時候要在臺面上找到Z低點。就是手動多走一會，看哪里洗不到，在Z低點定Z原點。重疊率要高，這樣洗出來的臺面才更平整。

方法一：臺面常用PVC板做底，在軟件里畫個和臺面一樣大小的距形，然后2D洗底，和平常洗雙色板一樣的。

換一個粗一點的麻花刀，洗起來就快了。下刀深度要根據情況而定，基本上是深底到?jīng)]有凹的地方為佳。洗完后打掃一下就可以了。

方法二：用專用的清底刀。

找到機器臺面的Z低點然后把刀下0.5-1mm深，然后啟動主軸手動操作來回跑可以了，注意：根據臺面材質的不同選擇不同的進給速度。

木工雕刻機清洗的方法很簡單并不麻煩，且保養好機器能夠延長機器的使用壽命，所以定期清洗臺面是非常有必要的，不要偷懶哦!

People who have used the engraving machine for a long time know that the use of the engraving machine countertop for a long time can easily lead to uneven burrs.In this case, if the machine is engraving, it is easy to cause the board to be uneven. When carving, it is easy to have flower knives, many burrs in the pattern, and it is easy to directly carve the board wrong, so it is very necessary to properly clean the countertop.So how to clean the countertop of the woodworking engraving machine?Let Xiaobian tell you two small methods.

First make a rectangular bottoming path map of the size of the countertop, and the depth should not be too deep.The key point is to find the Z low point on the countertop when facing the knife.Just walk manually for a while, see where you can't wash it, and set the origin of Z at the low point of Z.The overlap rate should be high, so that the washed countertop is smoother.

Method 1: PVC board is commonly used as the bottom of the countertop. Draw a pitch shape of the same size as the countertop in the software, and then wash the bottom in 2D, the same as the usual two-color board.

Change to a thicker twist knife and it will wash quickly.The depth of the knife should be determined according to the situation, basically it is better to have a deep bottom to a place where there is no concave.Just clean it up after washing.

Method two: Use a special bottom-clearing knife.

Find the Z-low point of the machine countertop and put the knife 0.5-1mm deep, then start the spindle to run back and forth manually. Note: Choose different feed speeds according to the different table materials.

The cleaning method of woodworking engraving machine is very simple and not troublesome, and maintaining the machine well can extend the service life of the machine, so it is very necessary to clean the countertops regularly. Don't be lazy!